Dual Column Hydraulic Metal Profile Metal Popular Bandsaw Machine
1. The operation of the sawing machine must undergo professional
training and master the operation skills of the band sawing
machine. The operators shall ensure their concentration. Before
operation, they shall wear tight protective clothing, fasten the
cuffs, keep the lower part of the coat closed, and shall not wear
gloves. They shall not wear, take off or change clothes near the
moving machine tool, or cover the body to prevent the machine from
being twisted. Must wear eye protection, ear plugs, not shorts,
slippers.
2. Before starting the machine, make all preparations. First, check
whether the coolant is sufficient, whether the cooling nozzle is
normal, and whether the air compressor is normally started.
3. Before sawing, it is also necessary to check whether the
aluminum cutting on the aluminum material filter screen is clean
and whether there is no aluminum cutting on the sawing table to
ensure the table is clean.
4. Saw table must be flat. Idle for 1-2 minutes before sawing, and
check whether the sawing machine has any fault and whether the
lubricating oil circuit is normal.
5. Adjust the length positioning according to the size of the
processed workpiece. After adjustment, the positioning device must
be locked. A kind of
6. When sawing pipe or thin plate sections, the tooth pitch shall
not be less than the thickness of the material. When sawing, the
handle should be back to the slow position and the feed amount
should be reduced.
7. After the positioning is adjusted, when opening the saw blade,
pay attention to that the body part should not be close to the in
and out position of the saw blade, and keep away from the side. At
the same time, don't look at the direction of the saw blade on the
face to prevent the aluminum cutting from scratching the eyes and
face. Chinese style
8. When sawing the aluminum material with angle, the angle plate
(or angle clamp) shall be adjusted first, and the angle shall be
measured to meet the requirements of the drawing, then the angle
plate (angle clamp) shall be locked and positioned. Chinese style
9. In the process of sawing machine operation, if any abnormal
sound is found and the strength of the sawing machine is not
strong, the power supply of the sawing machine shall be turned off
immediately to check whether the parallel key components such as
the saw blade are normal, if any, it shall be reported in time, and
the professional maintenance personnel shall be informed to repair,
maintain and maintain the equipment. To be careful
10. After the work is completed, cut off the power supply, put each
control handle back to the empty position, and do a good job of
cleaning. A kind of
11. Add lubricating oil and sufficient coolant as required. Check
whether all parts are normal during empty running. If any fault is
found during the operation of the machine tool, stop the machine
immediately and report to the construction and support department
for repair. A kind of
12. When cutting the machine tool, do not measure the size and use
hands or tools to approach the saw blade and saw seam. A kind of
13. Power must be cut off at the end of each shift. Open the
protective cover. Remove the chips, wipe them clean, and do a good
job in daily maintenance and cleaning the surrounding environment
| Type | SH-450 |
| Cut capcity W*H (mm) | round 300 |
| square 300*300 |
| Bundle cutting W*H (mm) | Max. 320*180 |
| Min. 200*20 |
| Saw belt size(mm) | 5450*41*1.3 |
| belt line speed(m/min) | 15-80 frequency control |
| Main generator power(kw) | 3 |
| Hydraulic generator power(kw) | 1.5 |
| Cooling generator power (kw) | 0.09 |
| Working clamp style | Hydraulic |
| Saw belt tighten style | Hydraulic |
| Main trasmit structure | Turbine |
| Loading style | Extra roller |
| Volume of oil case (L) | 80 |
| Volume of water case (L) | 50 |
| Max single feeding (mm) | 500 |
| Working table height (mm) | 650 |
| Weights of machine (kgs) | 2600 |
| Packing dimensions(mm) L*M*H | 2400*7700*1800 |
